ANSATEK
Projects

Hardware we designed

Projects developed at ANSATEK, from control and power boards to modular system components.

Sensored Brushless Motor Controller (ESC)
Power Electronics

Sensored Brushless Motor Controller (ESC)

A three-phase brushless DC motor controller with Hall sensor feedback, designed for a 36 V bus. A dedicated half-bridge gate driver per phase, bootstrap-supplied high-side drive and wide phase traces were used.

Layers
2
Size
68.5 × 75 mm
Main structure
STM32F401, 3 × IR2103S, 6 × IRF3205
Interfaces
Hall sensors, USB-C, I²C LCD, potentiometer
BLDCHalf-BridgeGate DriverHall SensorSTM32
View details
Blood Slide Stainer Main Control Board
Medical Device

Blood Slide Stainer Main Control Board

The main board of a laboratory blood slide stainer, driving the pump, electromagnet, fan and Peltier loads from a single controller. Three switching regulators distribute 12 V, 5 V and 3.3 V from one input; the control and load sides are separated by optocouplers.

Layers
2
Size
200 × 90 mm
Main structure
STM32F4, 3 × XL4015, 2 × VNH2SP30, 2 × TB6612FNG
Interfaces
RS-232, sensor inputs, SWD
STM32Motor DriverBuck ConverterOptocouplerRS-232
View details
STM32F401 Mini Controller Board
Embedded Systems

STM32F401 Mini Controller Board

A compact microcontroller board that can be used as a development board or as a controller module inside a larger system. The angled placement of the controller shortens the traces to the pin rows on both edges and reduces the board area.

Layers
2
Size
53 × 23 mm
Main structure
STM32F401RCT6, 32 Mbit SPI flash
Interfaces
USB-C, SPI, GPIO headers
STM32Cortex-M4USB-CSPI FlashCompact Layout
View details
Battery Systems

BMS-01 — Battery Management System

A battery management board providing cell monitoring, passive balancing and protection for 35 V and 20 A continuous current. Over-charge, over-current and temperature protection are implemented in hardware.

Layers
2
Size
120 × 120 mm
Main structure
STM32 F series, cell monitoring and balancing stage
Interfaces
Isolated CAN
Cell MonitoringBalancingIsolated CANThermal Sensing
Power Electronics

PTM-01 — Power Transfer and Monitoring Module

A module handling current and voltage monitoring, MOSFET drive and protection on a 35 V, 20 A continuous (30 A peak) power transfer line. Wide copper areas and multiple-via structures were used on the high-current paths.

Layers
2
Size
120 × 250 mm
Main structure
STM32 F series, MOSFET driver stage, shunt measurement
Interfaces
CAN
MOSFET DriverShunt SensingCANHardware Protection
Sensor Systems

NAU-01 — Navigation and Attitude Unit

A sensor-fusion board that combines accelerometer, gyroscope and magnetometer data for orientation and motion analysis. The sensors sit on a noise-isolated reference plane, and the I²C and SPI lines are protected against EMI.

Layers
4
Size
85 × 120 mm
Main structure
STM32 F series, 9-axis sensor set
Interfaces
I²C, SPI, CAN
IMUSensor FusionEMI ShieldingCAN
Communication Systems

DCU-01 — Data and Communication Unit

A central communication board managing data traffic and telemetry between system modules. Data integrity is protected by CRC-based hardware verification, and the connector inputs are ESD-filtered.

Layers
4
Size
80 × 50 mm
Main structure
STM32 F series
Interfaces
CAN, UART, RS-485
CANRS-485ESD ProtectionCRC
User Interface

HMI-01 — User Interface Board

An LCD/TFT-based interface board that displays system status and handles user input. A fixed reference plane is reserved for the capacitive keys, and key inputs pass through hardware debounce filters.

Layers
2
Size
80 × 50 mm
Main structure
STM32 F series, LCD/TFT driver
Interfaces
UART, CAN, capacitive keypad
HMILCDCapacitive InputUART
EKASS.AI
System project

EKASS.AI — AI-Assisted Pedal-Assist System

A pedal-assist system for electric bicycles, currently at the design stage. It is built around sensor fusion, riding modes and an assist logic that keeps the rider's effort constant. Its initial development was supported by KOSGEB.

Sensor fusionRiding modesPedal assist
Visit the site

Let's talk about your project

Tell us about your hardware need or R&D idea, and we will clarify the scope and the steps together.

Get in touch